(2) Rockville RKL80MB 8" Marine Dual Wakeboard Tower LED Speakers+Amp+Receiver

$98.99 ~~$734.85~~

Qty. :

Category : Car Audio

Description
Warranty Information

Package Includes:

(2) Pairs of Rockville RKL80MB 8" 900 Watt Black 2-Way Marine Boat Speakers w/LED's
(1) Rockville DBM45 4-Channel 2000w Peak/500w Dyno-Certified RMS Marine/Boat Amplifier
(1) Rockville RMWK4 4 AWG Gauge Waterproof Marine Amplifier/Amp Install Wire Kit
(2) Rockville DMAC80B Dual 7.7" Black Aluminum Wakeboard Tower Speaker Enclosure
(1) Rockville RGHR2 Marine Gauge Hole Receiver w Bluetooth USB, Radio + Wired Remote

Video of RKL80MB:

Includes:

Pair of 8" Marine LED Speakers
16.4 feet of Speaker Wire
Stainless Steel Mounting Screws
Pair Black Grills

Features:

Pair Rockville RKL80MB 8 2-Way 900 Watt Black Marine Boat Speakers with LED Lights
Power Rating: 450 Watts Peak /100 Watts RMS Per Speaker
Total Power Per Pair: 900 Watts Peak / 450 Watts RMS
Beat sync LEDs flash to the rhythm of the music
You can select either red or blue color LEDs on the wire harness
No extra installation for the LED. It gets a power signal through your speaker wire
The louder the music the more intense the LEDs flash
IP66 waterproof rating
Fully Marinized Against Salt & Fresh Water Conditions
UV treated cone makes this completely Waterproof and rustproof
Anti-corrosion Stainless Steel Terminals
Molded ABS plastic for amazing sound and protection from the elements while out on the water
Polypropylene Formed Cone
22 Oz Y30 magnet supports high power handling
Rubber Surround
High quality ferrite magnet
1 inch PEI Tweeter
8 Woofer with Oversized 1.2 CCAW Kapton Voice Coil
Pre-installed Stainless-Steel mounting screws included
Perfect for Marine, Car, ATV and UTV applications
Impedance: 4-Ohm
Frequency Response: 40Hz - 20KHz
Sound Pressure Level: 89dB @ 1w/1m
Total Diameter: 8.07
Cutout Diameter: 6.89
Total Height: 4.84
Mounting Depth: 3.54
Perfect for marine, ATV, outdoor use

How To Set Up Your DMAC65 and DMAC80 Wakeboard Tower Speaker Pods:

Video of DMAC80B:

Includes:

1 Double Wakeboard Can
All mounting hardware
(2) 2.375 rubber inserts
(2) 2.25 rubber inserts
(2) 2.5 rubber inserts
(2) 2 rubber inserts

Rockville is proud to introduce our all new line of aluminum wakeboard cans. The DMAC80B features double pod design which allows you to mount two 7.7 speakers. It includes our rugged universal aluminum clamp for easy installation to any wakeboard tower pole measuring from 2" to 2.5" diameter. Six precision molded high impact rubber inserts guarantee fitment on towers from 2 to 2.5. Our clamp inserts are precision-fitted to sit perfectly inside the metal clamps. The speaker terminals are safely enclosed inside the waterproof speaker canister. ***Please note if you need an insert to accommodate a 1.75" diameter tube please let us know and we will send one out to you free of charge!This awesome double pod is built of super strong aircraft grade 6061 aluminum. The DMAC80B features a black powder-coat finish which offers unparalleled resistance to chipping, scratching, and fading. It is fully marinized which means it will withstand the elements on the water. This unit is 100 % waterproof. What makes our technology the best on the market is that our pods are internally wired! This means the terminals are inside the pod and the wires are fed through pre-drilled holes on the pod and clamp. Simply align the wire opening with the hole on your tower and you are done! No exposed wires or terminals! Aluminum cans will last forever!The sound quality of these are phenomenal! These are the perfect amount of air space to give you the perfect sound quality with the leading marine speakers on the market from brands like Kicker, Rockford Fosgate, etc. Our high efficiency design means more audio output from the same speakers! This means you get louder, cleaner sound with less distortion using our wakeboard enclosures than with other brands. Features:

1 Rockville DMAC80B black aluminum double can wakeboard tower enclosure
Made of high quality 6061 aircraft grade aluminum
Beautiful black powder-coat finish
100% waterproof and fully marinized against salt and fresh water conditions
Internally wired for clean installno exposed wires or terminals
High efficiency design features the perfect airspace for 7.7 speakers
Rugged universal mounting clamps made of 6061 aluminum
Includes precision molded, high impact plastic inserts for tower fitment from 2 diameter to 2.5 diameter
Mounting depth (in inches): 7.4"

All about your RGHR2:

How To Set Up Your RGHR2:

Included in the box:

Marine digital media receiver
Wired remote with 32.8 foot wire
USB extension cable (40 inches)
Mounting bracket
Screws
ISO wiring
Owner manual and warranty

Description:

The Rockville RGHR2 is the best gauge hole receiver on the market. We developed this to give you the best sound and the best features.

Crazy loud!We put in a built in amplifier that is louder than other marine receivers on the market. The RMS power of the built in amp is 28 watt x 4 channels! It is crazy loud and can be heard over the sound of the wind when you are on the water! There is also a built in EQ to customize the sound to your taste.

Included wired remoteRockville is the only brand on the market that I know of that supplies a wired remote with your radio. The wired remote is a must have for any marine radio. This is great for boats and other powersport applications. We also include an extra long 32.8 foot wire so you will not need any additional extension cables.

Latest listening featuresThe RGHR2 gives you many listening options. The Bluetooth technology allows you to stream audio from your Bluetooth enabled phone or other music player to the receiver. Our Bluetooth distance is 50 feet! There is also a USB input allowing you to listen to music stored on a thumb drive. You can plug in any audio device to the auxiliary input. There is a built in radio with crystal clear reception as well.

Ability to connect multiple external ampsThis receiver makes your system expandable. Two sets of pre-amp outputs allow you to hook up external amps for your speakers and/or subs. This has front and switchable rear/sub pre-amp outputs so you can amplifiy your speakers and a subwoofer amplifier.

Features:

Rockville RGHR2 Weather Resistant Gauge-Hole Digital Media Receiver w/Bluetooth/USB/AM/FM
Fits into a standard Gauge-Hole (Tachometer) Opening
Built-in 72 x 4 Watt Peak high powered amplifier (28 x 4 RMS)
Built in EQ with preset EQ curves (Pop, Class, Rock, Flat)
IP66 Waterproof Certification (Tested to withstand the elements)
USB Input to play back audio files store on a USB thumb drive or any other USB device
RCA Aux Input
AM/FM Radio Built In with 18 FM and 12 AM presets + US and European tuning
Bluetooth built in to stream audio from any Bluetooth enabled device
USB Input Charges Your Phone
Two Sets of RCA Outputs (Front and a switchable rear/sub) allow you to connect external amplifiers
Big easy to use buttons
Backlit LCD display
Wired Remote Control Included (normally $50)
Required cutout: 2.96" (diameter) x 2.75" (depth)
USB is 500mA and 5V and supports 16GB max
Dimensions:
2.96" cutout mounting diameter
4.45" diameter top plate
3.9" mounting depth (not including top plate)
5.0" depth including the top plate
Specs of the built in amplifier:
TDA7851L quadbridge power amplifier
4 x 72 watts peak @ 2 ohm
4 x 48 watts peak @ 4 ohms
4 x 28 watts RMS @ 4 ohms
Highly efficient even when running at 2 ohms!
Low distortion even at top volumes

Video of RMWK:

Features:

Rockville RMWK4 4 AWG Gauge Waterproof Marine/Boat Amplifier Wire Installation Kit
20 Translucent, Twisted Pair, High Quality, Tinned-OFC Flexible PVC RCA Cable
18 4 Gauge High Current, Low Impedance, Clear Flexible Power Cable with 3 Black Poly Woven Mesh to better resist chemicals in the battery compartment
18 4 Gauge High Current, Low Impedance, Light Blue, Flexible Ground Cable
25 16 Gauge 100% Tinned-CCA, White, Non-Transparent Resin PVC, Flat Speaker Cable
25 Blue Remote Wire
(1) Silver Mini-ANL Fuse Holder Clear Shell and Clear Blue Bottom Bracket with Blue Waterproof Ring
(1) 120A Mini-ANL Fuse
(1) 80A Mini-ANL Fuse
(2) Ring Terminals
(2) Spade Terminals
(5) Speaker Cable Terminals
(1) Washer
(10) White Cable Ties

How To Install a Marine Amplifier onto Your Boat:

Video of DBM45:

What's in The Box:

DBM45 amplifier
PA microphone
Birth sheet with tested power
Mounting screws
Warranty card
Owners Manual

Description:

The all new dB marine series of amplifiers gives you the best of both worlds! We took the sound of our best-selling series of dB car amps and we added top of the line marine grade parts so that they will last forever and withstand even the harshest conditions on the water.We went a little overboard (no pun intended) to make this amp marine ready. We conformal coated the PCB board with a waterproof glue that is painted on to protect the circuitry. We then added waterproof silicone covers over the terminals so that water can never get into the amp. The heat sink, including the bottom plate, is made of aluminum which is rustproof. The end panels, internal mounting screws and hardware of the amp are made of stainless steel and are rustproof. Even after many years of use the amp will be rust free and operate like new!

The DBM45 is a 4-Channel high power amplifier with 2,000 watts peak output and 500 wattsDyno Certified power.Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market.The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS rating can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.

This amp has a very cool fully adjustable 12dB/Octave crossover. What is cool about it is that our crossover supports low pass, high pass, bandpass, and subsonic. This makes our amp ideal for subwoofers (sealed and vented), full range speakers, and midrange speakers. In high pass mode we allow you to filter out frequencies between 15Hz - 4K Hz. In full mode you will not be filtering any frequencies. The really cool part is in low pass mode you can use the high pass and low pass mode. So for example you can set the low pass mode to 50 hz, and then you can set the high pass to 15 Hz. In this case you would be playing frequencies in the range of 15-50 Hz on this channel. This would be an example of using the subsonic filter. Another option you have is for midrange speakers, you can use our low pass filter and set it really high. Lets say to 150 hz. And then you can set the high pass to 3K hz and your midrange speakers will only play that frequency range. Our advanced crossover technology will allow you to really fine tune each speaker to get the sound you desire.

The dBM45 is protected by a fully IC controlled circuit which includes mute, delay, soft start technology so that the amplifier will turn on safely every time and protect your speakers from popping.

We are so confident in your satisfaction with this amplifier that we will offer you a 90 day money back guarantee. If this amp does not perform as well as you expected, we will send you a pre-paid shipping label and give you your money back. This means that, if for any reason you want to return the amplifier for a full refund within 90 days, you can! (Amp must be complete along with the box).

Features:

Rockville DBM45 4-Channel 2000w Peak/500w Dyno-Certified RMS Marine/Boat Amplifier
Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
2 Ohm: 125 Watts x 4 Channel
4 Ohm: 85 Watts x 4 Channel
4 Ohm Bridged: 250 Watts x 2 Channel
Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
2 Ohm: 500 Watts x 4 Channel
4 Ohm: 340 Watts x 4 Channel
4 Ohm Bridged: 1000 Watts x 2 Channel
Painted Conformal Coating PCB Board (Uses 2577 Waterproof Glue)
Waterproof silicone covers for end panels
Rustproof Aluminum heat sink with white painted finish
Stainless steel end panels are rustproof
All screws and mounting hardware are stainless steel and rustproof
Bottom panel is aluminum and rustproof
All channels on the amp have crossovers so they can each be used for subs or full range speakers or tweeters or midrange speakers
All channels on the amplifier are bridgeable
Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
Adjustable Subsonic Filter: 15Hz -40Hz (This filter is on the HPF knob)
Adjustable Low Pass Filter: 40Hz 4KHz
Adjustable Band Pass Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter)
Adjustable High Pass (Subsonic) Filter: 15 Hz - 4 kHz (use both the HPF and LPF filter)
Fully Adjustable 12dB Bass Equalizer
2CH/4CH Input Mode Switch
Status Mode LED Indicator
Adjustable Input Level Control
Mute and Delay Soft Start System
Minimum THD at Rated Power: <0.05%
S/N Ratio: >90 dB
Frequency Response: 10 Hz - 50 kHz
Damping Factor: >85 @ 100Hz
(2) 35 Amp ATC Fuses
High-Speed MOSFET Power Supply
Studio-Grade Bipolar Output Stage Transistors
8 Volt Preamp Circuitry
35 Amp x2 ATC Fuse
Microphone input and PA microphone included
Product Dimensions (W x H x L): 9? x 2.4? x 15.1? inches
Product Weight: 7.7 Lbs